证券配资歡迎您的到来!


专业研發生産墓碑雕刻機、证券配资、小型玉石雕刻機、木工開料機、浮雕雕刻機、數控開料機等數控雕刻機械!
富余通配资
全國客服熱線:

18753111288

行业新聞

雕刻機出現錯位怎麼辦?

  雕刻機在雕刻過程中出現各種錯位缺點,如左右錯位、上下錯位、x軸錯位、z軸錯位等等,終究是什麼緣由致使雕刻機出現錯位表象呢?

  1.檢查雕刻軟件的途徑正确與否;

  2.檢查絲杆的空地巨細及光杆的緊固螺絲有沒有松动;

  3.檢查軟件參數的設置正确與否。

  4.檢查地線是不是接好

  5.電腦是不是有病毒或許與其他不兼容或許煩擾,一般主張無須品牌機簡略拼裝機箱即可

  6.水冷主軸電機前上方的聯軸器是不是松动損壞可檢查用手擰緊或許替換

  7.雕刻機橫梁上到機器控制箱聯接拖鍊的線是不是有接觸不良

  8.驅动器的疑問:驅动器本身里面的布局或許電子原器材有疑問也會構成錯位表象,这個緣由最多;若出現的次數不多,而且把速度下降一點,有時能正常雕刻,这說明驅动器還沒有徹底壞掉;若是一開始雕刻就錯位就說明驅动器徹底壞了。處理方法:修補驅动器或許替換驅动器。

  9.電壓的疑問:雕刻機在作业時需求的功率大,若是電壓過低,給驅动器供電缺少,功率达不到則會構成錯位表象,这種情況一般以Y軸錯位为多,出現这種表象有可能是外界電壓不可,或許在同一線路上有人使用了大功率的設備如電焊等。處理方法:裝置一個5000瓦的穩壓電源,但这個穩壓電源的過失規劃不能超過5%,最好在3%以内。

  10.接口闆,主闆,轉接闆的疑問:要是接口闆,主闆,轉接闆壞了,雕刻機在作业的過程中,某一個方向或許是三個軸均不动,構成雕刻錯位。

  主軸電機的疑問:要是步進電機或許是伺服電機的疑問,整個機器在某一方向上都不移动,用手轉絲杆也轉不动。

  11.機床本身的疑問:機床上的某個部件有疑問或許是松动,表面有雜質等也會出現錯位表象;如聯軸器松了,壞了,都會出現錯位;導軌,絲杆上長期沒有清潔加油也會出現錯位表象;機床線要是斷了也會出現錯位表象。

  各部分聯接控制線接觸不良(功控線傳輸線)。處理方法:将全部連線拆掉再裝

雕刻機

  In the process of carving, engraving machines appear various mismatches, such as left and right dislocation, up and down dislocation, X axis misalignment, Z axis misalignment and so on. After all, what causes it?

  1. the way to check the carving software is correct or not.

  2. check the hole in the rod and the fastening screws of the rod have not been loosened.

  3. check whether the software parameters are set correctly or not.

  4. check the ground line is not good

  5. computer is not a virus may be compatible with other incompatible or annoying, generally advocate without a branding machine simply assembled chassis can

  6. the coupling on the front of the motor of the main shaft of the water cooled main shaft is not loose and damaged, which can be checked by hand tightening or replacement.

  7. beam engraving machine to machine control box connected chain line is not bad

  8. questions: drive drive itself inside the layout of electronic equipment may doubt it will constitute the dislocation representation, the reason most; if the number is not much, but the speed drops a little, sometimes normal carving, the driver is not completely broken; if one starts carving dislocation that drive completely bad. Processing: repair the drive or replace the drive.

  9. questions: voltage power engraving machine in operation demand, if the voltage is too low, the lack of power supply to drive, not up to will be the formation of dislocation representation, this situation generally Y axis misalignment is much, this phenomenon may be external voltage can not, perhaps some people use high power equipment such as welding on the same line. Processing method: a 5000 Watt voltage regulator, but the fault planning of the voltage regulator can not exceed 5%, preferably within 3%.

  10. interface board, motherboard, transfer board question: if the interface board, motherboard and adapter plate are broken, the carving machine may be three axis in one direction, which will form a sculpture dislocation.

  The question of spindle motor is that if stepping motor is probably the doubt of servo motor, the whole machine will not move in a certain direction, and it will not be able to move by hand.

  11. questions: a machine parts on the machine in question may be loose, surface impurities also arise such as dislocation representation; coupling loose, broken, will appear on the screw dislocation; guide, no long-term clean fuel will also appear dislocation representation; machine tool line is broken will dislocation representation.

  Each part of the connection control line is in bad contact (the power line transmission line). Treatment: remove all the wires and reload

聯系我們

聯系人:張经理

手 機:18753111288

郵 箱:603543833@qq.com

公 司:富余通配资

地 址:濟南市高新區春晖路688号